85jeepn
03-17-2012, 12:22 PM
Time to face reality my work hours aren’t going down and my energy level isn’t going up and I am never going to get back to this project so It’s time to sell it off to fund other hobbies.
Everything is PLUS shipping unless other wise stated.
Everything is NEW unless other wise stated
-Rock Crusher D60 high pinion center section $650.00 SOLD
-Ruff Stuff D60 Diff cover welds smoothed and $90.00 shipped SOLD
POR 15 Black $80 if picked up
-D60 Detroit locker 35 spline $550.00 SOLD
-Dedenbear (Reid racing) D60 inner “C’s” $350.00 SOLD
-Solid Axle Industries High steer king pin knuckles w/ $500.00 SOLD
Custom high steer arms springless design
-Solid Axle Industries 35 spline drive flanges $175.00 SOLD
-Warm Premium 35 spline lockout hubs $200.00
-CTM D60 ujoints $550.00 SOLD
-D60 35 spline stub shafts 4340 chromoly w/ $300.00
Seal kit
-D60 inner shaft short side chevy chromoly $150.00
-D60 spindles 6 bolt chevy w/ nuts and washers $200.00 SOLD
-Stock used Chevy D60 caliper brakets very good $85.00
shape sand blasted and primed
-King pin kits lower bearing and seal, upper bushing, $75.00 SOLD
King pins and springs
-D60 Timken wheel bearings races and grease seals $50.00 shipped SOLD
-D60 custom made lower king pins $120.00SOLD
Never brake off bolts or grease zerk again
-D60 used dually hubs blasted and painted with $125.00
POR 15 w/ New rotors
-D60 bare housing long side tube cut off at knuckle $200.00
tube cleaned out of knuckle ready to be built to your
length Chevy stock
-D60 Stock brake calipers and pads NEW $65.00 SOLD
Located in Covington OH 45318
Email me at jjswabb@gmail.com
Everything is PLUS shipping unless other wise stated.
Everything is NEW unless other wise stated
-Rock Crusher D60 high pinion center section $650.00 SOLD
-Ruff Stuff D60 Diff cover welds smoothed and $90.00 shipped SOLD
POR 15 Black $80 if picked up
-D60 Detroit locker 35 spline $550.00 SOLD
-Dedenbear (Reid racing) D60 inner “C’s” $350.00 SOLD
-Solid Axle Industries High steer king pin knuckles w/ $500.00 SOLD
Custom high steer arms springless design
-Solid Axle Industries 35 spline drive flanges $175.00 SOLD
-Warm Premium 35 spline lockout hubs $200.00
-CTM D60 ujoints $550.00 SOLD
-D60 35 spline stub shafts 4340 chromoly w/ $300.00
Seal kit
-D60 inner shaft short side chevy chromoly $150.00
-D60 spindles 6 bolt chevy w/ nuts and washers $200.00 SOLD
-Stock used Chevy D60 caliper brakets very good $85.00
shape sand blasted and primed
-King pin kits lower bearing and seal, upper bushing, $75.00 SOLD
King pins and springs
-D60 Timken wheel bearings races and grease seals $50.00 shipped SOLD
-D60 custom made lower king pins $120.00SOLD
Never brake off bolts or grease zerk again
-D60 used dually hubs blasted and painted with $125.00
POR 15 w/ New rotors
-D60 bare housing long side tube cut off at knuckle $200.00
tube cleaned out of knuckle ready to be built to your
length Chevy stock
-D60 Stock brake calipers and pads NEW $65.00 SOLD
Located in Covington OH 45318
Email me at jjswabb@gmail.com