My Cj7 Build Buckminster

[jwend]

Ok we are making this thing a FREAK start it tuesday of this week. I will keep things updated on here and Carwash will on sigma motorsports, List of goodies as follows.

Front soa king pin chevy 60
behind axle high steer
Rear 14 bolt chevy 4link with
Ruff stuff spec disk brake conv set
Gen right front link mount
1 1/4 in currie Johnny joints
Blue torch fab Axle truss and pinion gaurd
Fox 2.5 in air shocks

New Sigma motorsports full custom cage with
Front and rear seat tie in's
Integrated propane tank mounts over wheel wells

New front and rear Sigma Motorsports bumpers with d ring mounts and stinger

New Sigma Motorsports Front tube fenders

Rims and tires
H1's 8 bolt
Great lakes recenters and rock rings
New 42x15x16.5 Pitbull rockers
Built by Carwash

Ford mustang Mineral gray paint on body with red cage

That is the first part of the build. SOON to come

Engine swap
Trading the 50k mile built amc 304 for a Highly moded sbc 350
Transmition swap
Trading the 3 speed for a rebuilt t400 auto
Transfer case
Trading factory dana 18 for a atlas transfer

Rock sliders to tie in cage

Add the gotpropane.com propane kit

Cv joint front axle shafts

Full spool rear locker
Detroit locker front locker

I am sure I am missing some stuff but its alot. I will post parts for sale in the for sale section on CORE If you want anything that comes off of it or coming off of it pm me for them. Thanks and enjoy

[jwend]

A few pics

[KargoMaster]

Nice, I'm sure CW will do her up right...

He helped me with BTF trusses...both 60 and 14bolt onto mine. I did have to shave a little casting flash off of the top of the 14... the clearance was very tight. Pinion support bolts, three bolts between the two pieces... all had to be just right...

I can't wait to see the tube fenders.... (Make a jig CW!!) Seems like you could comp cut a little closer to the tailg... oh wait, that's the edge of the body mount isn't it?

What travel 2.5" air shocks? (Boomhauer just got 16" that he's trying to fit under a comp cut, and mine are 18" but I don't have any body there anymore... )

I wanna know more about "Cv joint front axle shafts"...

If the Dana18 is the large intermediate shaft version I might be interested...


ps - I might have some deck expansion work for you...

[began]

those tires look familiar lol they look great on a JK. Jeeps going to be Badass when you get it done

[carwash]

Originally Posted by KargoMaster

Nice, I'm sure CW will do her up right...

He helped me with BTF trusses...both 60 and 14bolt onto mine. I did have to shave a little casting flash off of the top of the 14... the clearance was very tight. Pinion support bolts, three bolts between the two pieces... all had to be just right...

On yours, both pieces were already drilled weren't they? On this one, only the pinion mount is drilled, but the truss is a blank.

I can't wait to see the tube fenders.... (Make a jig CW!!) Seems like you could comp cut a little closer to the tailg... oh wait, that's the edge of the body mount isn't it?

yeah, need to make a jig for sure, might do it off this rig, as it seems very unmolested, unhit, untwisted etc... Make a fender, make the jig from that I guess. yes, the body mount is there, but i'm still pushing for a deeper cut... keeping the top curve corner the same and angling the bottom further towards the tailgate and losing that body mount. Easy to throw a new one in the middle if needed.

What travel 2.5" air shocks? (Boomhauer just got 16" that he's trying to fit under a comp cut, and mine are 18" but I don't have any body there anymore... )

yes, 16" travel, won't know where they're gonna go til we get them in there i guess. I see them coming into the rear tub a little.

I wanna know more about "Cv joint front axle shafts"...

http://www.rcvperformance.com/store/catalog/index.php A true CV, no u joints, guaranteed, etc. Getting very popular. Pricey, but they say you won't break em. I think well of $2k for the 60's. About the same price as my 2" 47 spline shafts once all said and done. Kirby runs them and JeffK5 also just bit it off and got some. They make them for the rockwells, but they use the same bell as the dana60... so that worried me.

If the Dana18 is the large intermediate shaft version I might be interested...


ps - I might have some deck expansion work for you...

[JeffK5]

Sounds like one hell of a parts list...should be a very capable rig.

Any ideas on wheelbase..belly height and the rest ?

[jwend]

No clue yet. I want to keep it wide and low slung. the soa in the front is going to make that up for us. and width im just not sure on yet

[jwend]

Came along well this week! We are gona have a tonn done for next week. All the backordered parts come in and or ship monday. This work is all done at Sigma Motorsports!!! Carwash is the man hit him up and get him to build somthing for you!!

[jwend]

one more for ya

[mckeddie]

joey's running rcv's on teh new buggy him and butch are making. those things are sweet.

hell of a parts list, looks good.

[jwend]

This week we got alot done, Propane installed and running, got the hummers done and rolling, fininshed up the four link and installed 18 fox air shocks, they didnt like the frame were it was so it had to go. pics

[gothodgie]

looking good brother... tires look even better on it...
can't wait to see it on the trail...

[KargoMaster]

Nice "Islander" door...

Great progress, and post up the numbers for the 4-link... please.

And I don't think I ever answered this... the 3 bolts for the 14bolt BTF truss... I vaguely remember drilling one side... but by the time CW saw it they were done...

[carwash]

Yeah, after getting it on and placing the truss and pinion guard where it went, it became evident that there was really only 1 place the holes could end up if you wanted the two plates to sit flat against each other. Odd to me that they didn't predrill them...

[carwash]

Originally Posted by KargoMaster

Nice "Islander" door...

Great progress, and post up the numbers for the 4-link... please.

This is the best I could get it... I was limited on the vertical separation at the axle by the truss itself and lower mounts. Vertical separation at the frame is set at max. It has 4 other positions, but none of them yielded any better numbers.

What helps quite a bit is the 10-12 degrees i got on the lowers with these brackets. While it's not a completely dual triangulated setup, it does have some on teh lowers which should stablilize it quite a bit and reduce the crab a little bit.

Anyways, it is what it is. 4 link numbers can be analyzed for days and changed here and there. And what looks good on paper doesn't mean **** once you try it out in real life, really. When i did the 4 link on the pumpkin 49 years ago, i just put **** where it looked right. And it worked awesome. LAter when i came across the 4 link calculator, i put the numbers in, and as far as the program says, the rig shouldn't even have worked at all. so, don't get too caught up in your numbers here, or make insane changes to your build and design just to get a couple more digits higher on you Anti Squat, ore whatever...

[jwend]

[QUOTE=KargoMaster;36614]Nice "Islander" door...

Mike wants me to paint it that way and keep the stickers, he is gay like that i think.

[yellowjacket]

wiring looks real clean.

Sent from my LS670 using Tapatalk

[carwash]

It takes crazy time to wires stuff like that... that's why i buy my panels pre made... i have appreciation for that kind of patience.

[Redriverranger]

Holy **** batman, that's a lot of switches. Turn the key and start the engine, turn the lights on, turn the wipers on, turn the heater on. The rest is overkill unless this is some kind of James Bond super spy mobile, with lot's of trick gadgets to keep everyone from making the same lines you make.... Looks good though..

[humpy]

Nice work dude

[jwend]

Originally Posted by Redriverranger

Holy **** batman, that's a lot of switches. Turn the key and start the engine, turn the lights on, turn the wipers on, turn the heater on. The rest is overkill unless this is some kind of James Bond super spy mobile, with lot's of trick gadgets to keep everyone from making the same lines you make.... Looks good though..

Yeah it is alot, i like to be able to control everything on its own, switches are for radio, each set of rock lights and what ever else i may want to add but yes i think i have only wired to 6 or 8 of the 12 and have no clue what i will use the others for i also double switched a few things.. back up learn that one from a good buddy, switch crapped out on us on the nasty side of grape vine hit the back up and we went on our way.. i am excessive

[jwend]

Yes the switch panel is my work.. i can do them for anyone interested at a small fee ..... Worked on this some more yesterday, got my skid plate started and changed my x member a little wanted to protect the transfer case a little more and give it some more support from rotating.. also got my bump stop mounts fabed up.. will post some pics of progress in a few days coming along nice.. going to be wednesday before i can work on it again.. want to have it done to play in the snow a little bit.

[yellowjacket]

looks good jason. looks like u been keepin on it

Sent from my LS670 using Tapatalk

[jwend]

Thanks dude.. its been alot of work. hope to be wheeling in a few weeks

[jwend]

Done, well except front shaft, waiting on parts be here this week. But its mobile gona clean it up real good this week and do some touch up paint then I wil take all the finished pics.