Parting out 96 XJ

Gunrunner · 01-23-2012, 10:29 AM

My son rolled his jeep awile back and we have him back on the road now with another one. It's time to get this roll over out of my yard/shop. There are no straight body panels or glass. They rolled it back up and drove it out of the woods. It wasn't a serious wheeler and had only been out a few times. It was his daily driver and had 190K on it. The motor trans and Tcase all worked great. We are going to part it out now and try to recoup some of the money I loaned him for the one he is driving now.
4.0L motor $250
4 speed auto trans $250
Tcase (NP241?) $200
Dana 30 front (new brakes) $100
Dana 35 rear (Trac-loc) $90
1.5" rear lift shackels $40
1.5" front spacers $40 (still on current jeep, off next week)
It has A/C and was holding pressure but was low.
No ABS
Grey cloth interior is OK but needs cleaned (Wet/glass)
If there is anything else you might need let me know, it's going to the salvage yard this weekend or early next week, and anything not priced above is going with it.

All prices negotiable and I accept quality Firearms in trade (no jennings or Hi-point please)

cincygman · 01-23-2012, 12:52 PM

Is d30 a HP and what gear ratio

Gunrunner · 01-23-2012, 01:15 PM

I will check and post back in a few hours

WrenchMonkey · 01-23-2012, 04:38 PM

Stock would be high pinion, and 354s...

Robert

Gunrunner · 01-23-2012, 06:31 PM

Quote:

Originally Posted by WrenchMonkey

Stock would be high pinion, and 354s...

Robert

What he said, I checked and it is high pinion, ratio tag missing but BOM tag still there. Numbers as follows:

52060194
55 610502-7

DANA BOM sheet says 1994-1997 XJ Dana 30 front open 3.55 ratio.

Axle is still under jeep so I can roll it up on the trailer to take it to the salvage yard. Going to roll it up and then pull it on the trailer and set it down on a couple of wood planks. Should be out by this weekend.

GPER · 01-23-2012, 07:13 PM

How far are you from Dayton, how much for the brake booster, and master cylinder?????? Do you think they would fit my 94 xj?????

Gunrunner · 04-16-2012, 02:14 PM

OK, the Jeep is long gone but I've been tripping over the axles, motor, trans and t-case long enough.

$50 each for axles, engine, trans or T-case, they are worth that in scrap.

mossyoaktj · 04-16-2012, 04:09 PM

pm'd

Gunrunner · 04-16-2012, 06:38 PM

Front sold pending funds

biggin69 · 04-16-2012, 07:22 PM

Are the windshield washer nozzles still good?

gothodgie · 04-17-2012, 12:21 AM

Quote:

Originally Posted by biggin69

Are the windshield washer nozzles still good?

:confused:... for your buggy?

01-23-2012, 10:29 AM	#1
Gunrunner Join Date: Jan 2007 Location: Dry Ridge, KY Posts: 40	Parting out 96 XJ My son rolled his jeep awile back and we have him back on the road now with another one. It's time to get this roll over out of my yard/shop. There are no straight body panels or glass. They rolled it back up and drove it out of the woods. It wasn't a serious wheeler and had only been out a few times. It was his daily driver and had 190K on it. The motor trans and Tcase all worked great. We are going to part it out now and try to recoup some of the money I loaned him for the one he is driving now. 4.0L motor $250 4 speed auto trans $250 Tcase (NP241?) $200 Dana 30 front (new brakes) $100 Dana 35 rear (Trac-loc) $90 1.5" rear lift shackels $40 1.5" front spacers $40 (still on current jeep, off next week) It has A/C and was holding pressure but was low. No ABS Grey cloth interior is OK but needs cleaned (Wet/glass) If there is anything else you might need let me know, it's going to the salvage yard this weekend or early next week, and anything not priced above is going with it. All prices negotiable and I accept quality Firearms in trade (no jennings or Hi-point please) __________________ There are no stupid questions, but the world is full of inquisitive idiots.

01-23-2012, 12:52 PM	#2
cincygman Join Date: Nov 2008 Location: Pleasant Run Farms (near Fairfield) Posts: 378	Is d30 a HP and what gear ratio __________________ Romans 7-8

01-23-2012, 01:15 PM	#3
Gunrunner Join Date: Jan 2007 Location: Dry Ridge, KY Posts: 40	I will check and post back in a few hours __________________ There are no stupid questions, but the world is full of inquisitive idiots.

01-23-2012, 04:38 PM	#4
WrenchMonkey Mechanical Animal - CORE Member - - Moderator - Join Date: Feb 2008 Location: Beechmont Posts: 1,883	Stock would be high pinion, and 354s... Robert __________________ DIRTY DEEDS, DONE DIRT CHEAP Whatever doesn't kill you makes you stranger

04-16-2012, 02:14 PM	#7
Gunrunner Join Date: Jan 2007 Location: Dry Ridge, KY Posts: 40	OK, the Jeep is long gone but I've been tripping over the axles, motor, trans and t-case long enough. $50 each for axles, engine, trans or T-case, they are worth that in scrap. __________________ There are no stupid questions, but the world is full of inquisitive idiots.

01-23-2012, 07:13 PM	#6
GPER Join Date: Feb 2007 Location: Kettering, Ohio Posts: 811	How far are you from Dayton, how much for the brake booster, and master cylinder?????? Do you think they would fit my 94 xj?????

04-16-2012, 04:09 PM	#8
mossyoaktj Join Date: Apr 2008 Location: moscow,ohio Posts: 245	pm'd __________________ UNITED STATES MARINE 99 TJ, locked, long armed, creepy's

04-16-2012, 06:38 PM	#9
Gunrunner Join Date: Jan 2007 Location: Dry Ridge, KY Posts: 40	Front sold pending funds __________________ There are no stupid questions, but the world is full of inquisitive idiots.

04-16-2012, 07:22 PM	#10
biggin69 Really??? Join Date: Sep 2009 Location: Cincy Posts: 678	Are the windshield washer nozzles still good?