where to get driveshafts made?

nickhuts · 05-07-2012, 07:14 PM

Cincy Driveline? where have you guys had luck? I am in the market to get one made and one stretched out

jwend · 05-07-2012, 09:57 PM

the guys at cincy drive line are awesome. tom woods drive shafts are not prices bad at all either for what you get

kirbyiv · 05-07-2012, 10:04 PM

give Tom at Carolina Driveline a call. Not local, but his prices on driveshafts are still less than getting one local even after shipping. Tell him Kirby sent you and he will knock off a few bucks. 866-742-3848

coachholland · 05-08-2012, 09:04 AM

I run Tatton's front and rear. He's just down the road from Tom Woods, equal in quality but a bit less expensive. 801-685-0056 Same deal as Kirby... if you tell him Chris from JeepAddOns sent you he may give you a bit of a discount.

johnb1686 · 05-08-2012, 11:58 AM

X2 on the Carolina i have one of his. Drivetrain specialist in west chester is pretty good on price also if you want local

nickhuts · 05-09-2012, 07:59 AM

cool. thanks guys.

93 Krawler · 05-09-2012, 11:12 AM

I had Cincy driveline make me a front shaft for my rig. I told him I used it for rock crawling, and to make it strong. I also told him I needed a lot of slip in the shaft, and a cv joint.

They used that thin tube, which I destroyed, and a wimpy cv, that's destroyed, and the female end of the spline is only about 2" deep, so my shaft wobbles real bad. Personally, if you want a tough shaft, don't go there. I have better luck buying my own parts and doing them myself. They aren't balanced, but I don't drive it on the street.

nickhuts · 05-09-2012, 11:22 AM

Quote:

Originally Posted by 93 Krawler

I had Cincy driveline make me a front shaft for my rig. I told him I used it for rock crawling, and to make it strong. I also told him I needed a lot of slip in the shaft, and a cv joint.

They used that thin tube, which I destroyed, and a wimpy cv, that's destroyed, and the female end of the spline is only about 2" deep, so my shaft wobbles real bad. Personally, if you want a tough shaft, don't go there. I have better luck buying my own parts and doing them myself. They aren't balanced, but I don't drive it on the street.

Uh oh....don't tell me that! Just dropped them off yesterday....

93 Krawler · 05-09-2012, 01:24 PM

Quote:

Originally Posted by nickhuts

uh oh....don't tell me that! Just dropped them off yesterday....

doh...

05-07-2012, 07:14 PM	#1
nickhuts GRAB A SNATCH BLOCK!! Join Date: Jul 2007 Location: Monroe Posts: 197	where to get driveshafts made? Cincy Driveline? where have you guys had luck? I am in the market to get one made and one stretched out __________________ Powerstrokes, Mustangs, and Jeeps.. oh my

05-07-2012, 09:57 PM	#2
jwend Did I offend you? Join Date: Feb 2010 Location: Independence, ky Posts: 544	the guys at cincy drive line are awesome. tom woods drive shafts are not prices bad at all either for what you get __________________ Dont look @ me in that tone of voice or I WILL PUNCH YOU IN THE SHIRT! :mad:

05-08-2012, 09:04 AM	#4
coachholland Join Date: Feb 2012 Location: Winchester, KY Posts: 68	I run Tatton's front and rear. He's just down the road from Tom Woods, equal in quality but a bit less expensive. 801-685-0056 Same deal as Kirby... if you tell him Chris from JeepAddOns sent you he may give you a bit of a discount. __________________ Just another three linked stretched '95 YJ on 38s with a bunch of stuff scattered on the garage floor.

05-09-2012, 07:59 AM	#6
nickhuts GRAB A SNATCH BLOCK!! Join Date: Jul 2007 Location: Monroe Posts: 197	cool. thanks guys. __________________ Powerstrokes, Mustangs, and Jeeps.. oh my

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-07-2012, 10:04 PM	#3
kirbyiv Join Date: Apr 2009 Location: Cincinnati Posts: 27	give Tom at Carolina Driveline a call. Not local, but his prices on driveshafts are still less than getting one local even after shipping. Tell him Kirby sent you and he will knock off a few bucks. 866-742-3848

05-08-2012, 11:58 AM	#5
johnb1686 Join Date: Jan 2011 Location: Cincinnati Posts: 39	X2 on the Carolina i have one of his. Drivetrain specialist in west chester is pretty good on price also if you want local

05-09-2012, 11:12 AM	#7
93 Krawler >>>PMC<<< - CORE Member - - Administrator - Join Date: Sep 2010 Location: Ross, OH Posts: 2,069 Images: 1268	I had Cincy driveline make me a front shaft for my rig. I told him I used it for rock crawling, and to make it strong. I also told him I needed a lot of slip in the shaft, and a cv joint. They used that thin tube, which I destroyed, and a wimpy cv, that's destroyed, and the female end of the spline is only about 2" deep, so my shaft wobbles real bad. Personally, if you want a tough shaft, don't go there. I have better luck buying my own parts and doing them myself. They aren't balanced, but I don't drive it on the street.