Where can I get some exhaust work done?

4RunnerAdam · 04-27-2008, 08:21 PM

I'm going to need some exhaust work done on my 88 4Runner. I'm swapping in a carbed 350, and I'm not running cat converters. I'm going with dual exhaust with 2 glass packs. 2.75" probably. Needs to go from the block hugger headers all the way back. I usually have Ryan's Muffler do it, but they wont do it without installing cats. I don't feel confident enough in my welding skills to do it myself, unless I have to. So where can i get some work done that will do it without installing cats?

RD TRCTR · 04-27-2008, 09:00 PM

Maybe Morehaus's on Tealtown Rd. They do pretty good work. Are you going to run an X-pipe?

fabricator · 04-27-2008, 09:24 PM

Southside
2887 State Route 125
Bethel, OH 45106
(513) 734-2252

wilson1010 · 04-27-2008, 09:45 PM

If you take the plates off and trailer it in (or say you did), muffler guys will sometimes back off the cat requirement.

Bear Chow · 04-28-2008, 10:22 AM

Is this a trail vehicle. If so this is the best time to hone those welding skills. Especially if you already have the tools.

4RunnerAdam · 04-28-2008, 10:57 AM

the truckwill be registered and street legal. i dont have a trailer or i would try that. ill try the places mentioned. morehouse is just down the street i did not know they did exhaust. i want a leak free exhaust.

4RunnerAdam · 04-28-2008, 11:10 AM

and i was not planning on an x pipe. should i? i dont want to practice on the exhaust i hate leaky exhaust and my i dont trust my hf welder enough and my stick i dont think will be good at thin exhaust tube

Bear Chow · 04-28-2008, 12:49 PM

Again, is it a future trail vehicle? If so don't go with an X pipe unless you can really tuck it up there. You may have better luck trying to tightly fit an H pipe if you want to balance the exhaust.

If it's a street truck go for an X, they are real nice and can really help with the breathing.

4RunnerAdam · 04-28-2008, 03:44 PM

Its defietly a wheeler. I just dont call it a "trail vehicle" since I will drive it on the street too. I dont have a trailer so I have to drive it to and from the trails.

4RunnerAdam · 04-28-2008, 03:55 PM

Quote:

Originally Posted by fabricator

Southside
2887 State Route 125
Bethel, OH 45106
(513) 734-2252

They said they'd do it. Are they expensive? Do you have any experience with them?

RD TRCTR · 04-28-2008, 05:10 PM

I have experience with them. They do d@mn goodwork.

4RunnerAdam · 04-28-2008, 09:43 PM

Price? I dont want to pay a fortune.

Bear Chow · 04-29-2008, 09:10 AM

If you are going to have it professionally done. Take the time and talk to the actual welder that is doing the work. Describe how the vehicle is going to be used. Climb under there and find a way to really tuck it up tight. Don't forget heat shields where needed.

Good luck have fun.

WrenchMonkey · 04-29-2008, 09:19 AM

Quote:

Originally Posted by 4RunnerAdam

the truckwill be registered and street legal. i dont have a trailer or i would try that...

If southside falls through, and you need to tow it someplace else, let me know.

I've got the truck n trailer, and I'm just down GlenEste-Withamsville at Beechmont...

Robert

TomH · 04-29-2008, 07:00 PM

Quote:

Originally Posted by 4RunnerAdam

They said they'd do it. Are they expensive? Do you have any experience with them?

A buddy of mine used them on a Chevy deal and he loves them. They installed a takeoff cat-back and cut him a righteous deal.

04-27-2008, 08:21 PM	#1
4RunnerAdam Join Date: Apr 2007 Location: near eastgate mall Posts: 171	Where can I get some exhaust work done? I'm going to need some exhaust work done on my 88 4Runner. I'm swapping in a carbed 350, and I'm not running cat converters. I'm going with dual exhaust with 2 glass packs. 2.75" probably. Needs to go from the block hugger headers all the way back. I usually have Ryan's Muffler do it, but they wont do it without installing cats. I don't feel confident enough in my welding skills to do it myself, unless I have to. So where can i get some work done that will do it without installing cats?

04-27-2008, 09:24 PM	#3
fabricator Join Date: Jan 2007 Location: Cincy, Oh Posts: 947	Southside 2887 State Route 125 Bethel, OH 45106 (513) 734-2252 __________________ For you guys who can't drive, I have owned a frame rack for several years. Prices are based on your skill and ability to wreck it....

04-27-2008, 09:45 PM	#4
wilson1010 Join Date: Feb 2007 Posts: 147	If you take the plates off and trailer it in (or say you did), muffler guys will sometimes back off the cat requirement. __________________ Unimog 406 XJ with a bunch of stuff put on by somebody else

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-27-2008, 09:00 PM	#2
RD TRCTR Join Date: Nov 2007 Location: Troy, OH Posts: 94	Maybe Morehaus's on Tealtown Rd. They do pretty good work. Are you going to run an X-pipe?

04-28-2008, 10:22 AM	#5
Bear Chow Jeepless Join Date: Feb 2007 Location: Oxford, Oh Posts: 302	Is this a trail vehicle. If so this is the best time to hone those welding skills. Especially if you already have the tools.

04-28-2008, 10:57 AM	#6
4RunnerAdam Join Date: Apr 2007 Location: near eastgate mall Posts: 171	the truckwill be registered and street legal. i dont have a trailer or i would try that. ill try the places mentioned. morehouse is just down the street i did not know they did exhaust. i want a leak free exhaust.

04-28-2008, 11:10 AM	#7
4RunnerAdam Join Date: Apr 2007 Location: near eastgate mall Posts: 171	and i was not planning on an x pipe. should i? i dont want to practice on the exhaust i hate leaky exhaust and my i dont trust my hf welder enough and my stick i dont think will be good at thin exhaust tube

04-28-2008, 12:49 PM	#8
Bear Chow Jeepless Join Date: Feb 2007 Location: Oxford, Oh Posts: 302	Again, is it a future trail vehicle? If so don't go with an X pipe unless you can really tuck it up there. You may have better luck trying to tightly fit an H pipe if you want to balance the exhaust. If it's a street truck go for an X, they are real nice and can really help with the breathing.

04-28-2008, 03:44 PM	#9
4RunnerAdam Join Date: Apr 2007 Location: near eastgate mall Posts: 171	Its defietly a wheeler. I just dont call it a "trail vehicle" since I will drive it on the street too. I dont have a trailer so I have to drive it to and from the trails.

04-28-2008, 05:10 PM	#11
RD TRCTR Join Date: Nov 2007 Location: Troy, OH Posts: 94	I have experience with them. They do d@mn goodwork.

04-28-2008, 09:43 PM	#12
4RunnerAdam Join Date: Apr 2007 Location: near eastgate mall Posts: 171	Price? I dont want to pay a fortune.

04-29-2008, 09:10 AM	#13
Bear Chow Jeepless Join Date: Feb 2007 Location: Oxford, Oh Posts: 302	If you are going to have it professionally done. Take the time and talk to the actual welder that is doing the work. Describe how the vehicle is going to be used. Climb under there and find a way to really tuck it up tight. Don't forget heat shields where needed. Good luck have fun.